OWNER'S MANUALMODEL NUMBER:XT11530ESSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the
10The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety gla
11OPERATIONTO MOVE FORWARD AND BACKWARD (See Fig. 15)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction
12TO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each
13OPERATIONTO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter
14GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re
15MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention
16WARNING: To avoid serious injury, before performing any service or ad just ments:1. Be sure the on/off switch is in the OFF position.2. Remove saf
17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"
18SERVICE AND ADJUSTMENTSENGINESee engine manual.CARBURETORYour carburetor is not adjustable. Engine performance should not be affected at altitudes u
19STORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never store t
2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure
20TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.
21SERVICE NOTES
22REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.
23REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.
24REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.
25REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.
26REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.
27REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.
28REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA
29REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA
3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac -tured to give best possible dependability an
30REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA
31REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA
32REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT
33REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT
34REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT
35NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement
36KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)CHASSIS
37REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)WHEELSKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONNO
38REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)WHEELSKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U
39REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)BAG OF PARTSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIM
4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(1) LOCKNUT 5/16-18(751153)(1) CARRIAGE BOLT 5/16-18 x 5/8(72250505)(1) LOC
40REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)DECALSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTAN
41SERVICE NOTES
42SERVICE NOTES
43SERVICE NOTES
LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w
5ASSEMBLY / PRE-OPERATIONNOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the ski
6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins
7ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSUREThe tires on your snow thrower were overinflated at the fac-tory for shipping purposes. Correct and equal
8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with
9OPERATIONON / OFF switch - used to STOP the engine.Traction drive control lever - used to engage power-pro pelled for ward or reverse motion of snow
Comentarios a estos manuales